How to Replace Ignition Switch on 2019 Subaru: A Comprehensive Guide

Key Takeaways

  • Replacing the ignition switch on your 2019 Subaru is a straightforward process, but it requires some technical knowledge and tools.
  • You will need to disconnect the battery, remove the steering wheel, and take apart the steering column to access the ignition switch.
  • Make sure to follow the manufacturer’s instructions and safety precautions carefully to avoid damaging your vehicle or injuring yourself.
  • If you are not confident in your abilities to replace the ignition switch, it is recommended that you take your car to a certified mechanic.

Introduction

The ignition switch on your 2019 Subaru is responsible for starting the engine and controlling various electrical components in your vehicle. Over time, the ignition switch may wear out or become faulty, leading to problems with starting your car or other issues. In this guide, we will walk you through the process of replacing the ignition switch on your 2019 Subaru. By following these steps carefully, you can ensure that your car is running smoothly and safely.

See also  Unleashing the Power of Symmetrical All-Wheel Drive: A Closer Look at the 2015 Subaru Forester's Drivetrain

Step-by-Step Guide to Replacing the Ignition Switch on 2019 Subaru

Before you start, make sure you have all the necessary tools and equipment to perform the job. You will need a socket wrench, screwdrivers, pliers, and a steering wheel puller. Additionally, you should have a replacement ignition switch that is compatible with your Subaru model. Here are the steps to follow:

Step 1: Disconnect the battery

The first step is to disconnect the battery to prevent any electrical shock or damage. Locate the battery in the engine compartment and use a socket wrench to remove the negative cable from the battery terminal.

Step 2: Remove the steering wheel

Next, you will need to remove the steering wheel to access the ignition switch. Use a screwdriver to remove the screws that hold the horn pad in place. Then, remove the horn pad and disconnect the wires that connect it to the steering column. Use a socket wrench to remove the large nut that holds the steering wheel in place. Finally, use a steering wheel puller to remove the steering wheel from the column.

Step 3: Remove the steering column cover

With the steering wheel removed, you can now access the steering column cover. Use a screwdriver to remove the screws that hold the cover in place and gently pry it off.

Step 4: Remove the ignition switch

Once the steering column cover is removed, you will be able to see the ignition switch. Use pliers to remove any clips or wires that are attached to the switch. Then, use a socket wrench to remove the bolts or screws that hold the switch in place. Finally, gently pull the switch out of the steering column.

See also  Subaru 2.5-Liter Engine: A Smooth Ride on the Highway

Step 5: Install the new ignition switch

Take the new ignition switch and carefully insert it into the steering column. Make sure it is seated securely and use the bolts or screws to hold it in place. Then, reconnect any clips or wires that were attached to the old switch.

Step 6: Reassemble the steering column

With the new ignition switch installed, it’s time to reassemble the steering column. Replace the steering column cover and use a screwdriver to attach it with screws. Then, use the steering wheel puller to reinstall the steering wheel onto the column. Secure it with the large nut and reconnect the wires that connect the horn pad to the steering column.

Step 7: Reconnect the battery

Finally, reconnect the negative cable to the battery terminal and tighten it with a socket wrench. Test the new ignition switch by turning the key and starting the engine.

Conclusion

Replacing the ignition switch on your 2019 Subaru is a task that requires some technical knowledge and tools. However, by following the steps outlined in this guide, you can successfully replace the switch and ensure your car is running smoothly. If you are not confident in your abilities to perform this task, it is recommended that you take your car to a certified mechanic to avoid any damage to your vehicle or injury to yourself.

Frequently Asked Questions

Q: How do I know if my ignition switch needs to be replaced?

A: Signs of a faulty ignition switch may include difficulty starting the engine, the engine stalling or shutting off unexpectedly, or problems with the electrical components in your vehicle.

See also  A Step-by-Step Guide to Install Subaru Roof Racks

Q: Can I replace the ignition switch myself, or should I take my car to a mechanic?

A: If you have some technical knowledge and the necessary tools, you can replace the ignition switch yourself. However, if you are not confident in your abilities, it is recommended that you take your car to a certified mechanic to avoid any damage or injury.

Q: Are there different types of ignition switches for different Subaru models?

A: Yes, there are different ignition switches for different Subaru models. Make sure to purchase a replacement ignition switch that is compatible with your specific Subaru model.

Q: How long does it take to replace an ignition switch on a 2019 Subaru?

A: The time it takes to replace the ignition switch on your 2019 Subaru will depend on your level of experience and familiarity with the process. It may take anywhere from 2-4 hours to complete the task.

Avatar photo

Alton Brobst

As a longtime Subaru enthusiast, Alton brings a wealth of knowledge and experience to our blog. From his early days of tinkering with engines to his current role as a certified Subaru technician, Alton has seen it all when it comes to Subarus. When he's not working on cars, he enjoys hiking and exploring the great outdoors.

Recommended Articles