Billy Covington If you are a Subaru owner and you want to add some personality to your car, you might be interested in making your brake lights strobe. Not only does it look cool, but it can also increase your car’s visibility on the road. In this article, we will show you how to make all brake lights strobe in your Subaru.
Key Takeaways
- Making your brake lights strobe can increase your car’s visibility on the road.
- It is legal to have strobe lights in your brake lights in most states.
- You can make all brake lights strobe in your Subaru by installing a strobe module.
- Make sure to follow the instructions carefully and take necessary precautions when working with your car’s electrical system.
Materials Needed
To make all brake lights strobe in your Subaru, you will need the following materials:
- Strobe module
- Wire cutter/stripper
- Electrical tape
- Screwdriver
- Zip ties
Step-by-Step Guide
Follow these easy steps to make all brake lights strobe in your Subaru:
Step 1: Locate the Brake Light Wires
The brake light wires are located under the rear of your Subaru. You can access them by opening the trunk and removing the panels on the sides of the trunk. Once you have located the wires, use your wire cutter/stripper to strip a small section of the wire’s insulation.
🔍 Pro Tip: If you are unsure which wires are the brake light wires, consult your Subaru’s owner’s manual or look for a wiring diagram online.
Step 2: Install the Strobe Module
Now that you have located the brake light wires, it’s time to install the strobe module. The strobe module is a small device that controls the speed and pattern of the strobing lights. Follow the manufacturer’s instructions to install the strobe module in your Subaru. Typically, the module is installed by connecting the wires from the module to the brake light wires using electrical connectors.
📝 Note: Make sure to follow the manufacturer’s instructions carefully and take necessary precautions when working with your car’s electrical system. Always disconnect the car battery before working on the electrical system.
Step 3: Test the Strobe Module
After you have installed the strobe module, test it to make sure it’s working properly. Turn on your car and press the brake pedal to activate the strobing lights. If the lights are not working, check the wiring connections and make sure they are secure.
🛠️ Troubleshooting: If the lights still don’t work, check the fuse for the brake lights. If the fuse is blown, replace it and try again.
Step 4: Secure the Wiring
Once you have tested the strobe module and confirmed that it’s working, it’s time to secure the wiring. Use zip ties to secure the wires to the car’s frame and prevent them from moving around. Make sure the wires are not touching any hot or moving parts, and use electrical tape to cover any exposed wires.
🔒 Safety First: Always make sure the wiring is secure and not likely to come loose while you’re driving. Loose wires can cause a short circuit and potentially start a fire.
Step 5: Enjoy Your Strobing Brake Lights
Congratulations, you have successfully made all brake lights strobe in your Subaru! Enjoy your newly upgraded car and show it off to your friends.
🚘 Fun Fact: Strobe lights are legal in most states, but make sure to check your local laws to make sure you’re not violating any regulations.
FAQ
Q: Is it legal to have strobe lights in my brake lights?
A: In most states, it is legal to have strobe lights in your brake lights as long as they are not distracting to other drivers. However, it’s always a good idea to check your local laws to make sure you’re not violating any regulations.
Q: Can I install a strobe module myself?
A: Yes, you can install a strobe module yourself if you have basic knowledge of car electrical systems. However, if you’re not comfortable working with electricity, it’s best to consult a professional.
Q: How do I know if the strobe lights are working properly?
A: You can test the strobe lights by turning on your car and pressing the brake pedal. The lights should start strobing at the speed and pattern set by the strobe module. If the lights are not working, check the wiring connections and make sure they are secure.
Conclusion
Making all brake lights strobe in your Subaru is a fun and easy way to add some personality to your car. With the right materials and a little bit of know-how, you can install a strobe module and enjoy your new strobing brake lights. Remember to follow the instructions carefully and take necessary precautions when working with your car’s electrical system.
