Davis Bellew If you own a 2010 Subaru Forester, you may need to replace the brake light at some point. Luckily, it’s a relatively simple process that you can do yourself with just a few tools.
In this tutorial, we’ll walk you through how to replace the brake light on your 2010 Subaru Forester, step-by-step.
Key Takeaways
- Replacing the brake light on a 2010 Subaru Forester is a simple process that you can do yourself with just a few tools.
- You will need a Phillips head screwdriver, a flat head screwdriver, and a replacement bulb.
- The brake light is located on the rear of your Forester, and is accessed by removing the rear light assembly.
- Be sure to test your new brake light before reassembling your Forester’s rear light assembly.
Step-by-Step Guide
Step 1: Gather Your Tools
Before you begin, you will need a few tools to replace the brake light on your 2010 Subaru Forester. You will need a Phillips head screwdriver, a flat head screwdriver, and a replacement bulb. You can purchase replacement bulbs for your Forester at any auto parts store.
Step 2: Remove the Rear Light Assembly
The brake light on your 2010 Subaru Forester is located on the rear of your vehicle. To access it, you will need to remove the rear light assembly. To do this, you will need to use your screwdriver to remove the two screws that hold the assembly in place. These screws are located on the inside of the assembly, near the tailgate.
Once you have removed the screws, gently pull the rear light assembly away from your Forester. Be careful not to damage any of the wires that connect the assembly to your vehicle.
Step 3: Replace the Brake Light
With the rear light assembly removed, you can now access the brake light on your 2010 Subaru Forester. To replace the brake light, you will need to use your flat head screwdriver to carefully pry the old brake light bulb out of its socket. Be sure to take note of the orientation of the bulb before removing it, as you will need to install the new bulb in the same orientation.
Once you have removed the old bulb, insert the new brake light bulb into the socket. Be sure to push the bulb in until it clicks into place.
Step 4: Test the New Brake Light
Before you reassemble your Forester’s rear light assembly, be sure to test your new brake light. To do this, turn on your Forester’s headlights and press the brake pedal. The new brake light should light up.
Step 5: Reattach the Rear Light Assembly
Once you have tested your new brake light, you can reattach the rear light assembly to your 2010 Subaru Forester. To do this, simply line up the assembly with the holes where the screws were located, and reinsert the screws.
Step 6: Test Your Rear Lights
With the rear light assembly reattached, you should test all of your rear lights to make sure they are working properly. This includes your brake lights, turn signals, and reverse lights.
Congratulations, you have successfully replaced the brake light on your 2010 Subaru Forester!
Frequently Asked Questions
How long does it take to replace a brake light on a 2010 Subaru Forester?
Replacing a brake light on a 2010 Subaru Forester should take no more than 15-20 minutes.
How much does it cost to replace a brake light on a 2010 Subaru Forester?
The cost of replacing a brake light on a 2010 Subaru Forester will vary depending on where you purchase your replacement bulb. However, you can expect to spend anywhere from $5 to $20.
Why is it important to replace a brake light?
Replacing a brake light is important for several reasons. First, it is a safety issue. If your brake light is not working, other drivers may not be able to tell when you are braking, which could lead to an accident. Additionally, in some states, it is illegal to drive with a broken brake light. Finally, replacing a brake light is a simple and inexpensive way to keep your vehicle in good condition.
