How to Change Manual Subaru Forester Gear Shift

If you own a Subaru Forester with a manual transmission and you’re experiencing issues with the gear shift, you may need to replace it. This may seem like a daunting task, but with the right tools and some good instructions to follow, it can be a straightforward and manageable process. In this guide, we’ll walk you through step-by-step instructions on how to change the manual gear shift of a Subaru Forester.

Key Takeaways

  • Replacing the manual gear shift of a Subaru Forester is a manageable process
  • Ensure you have the right tools, including a torque wrench and a transmission jack
  • Take photos and notes as you go to make reassembly easier
  • Be patient and take your time, as rushing can lead to mistakes

Required Tools

Before you begin, you’ll need a few tools to get started. Here’s what you’ll need:

  • Socket set
  • Pliers
  • Torque wrench
  • Transmission jack
  • Socket extension
  • Gear shift kit (make sure it’s the right one for your specific make and model)

Step-by-Step Guide

Step 1: Remove the Gear Shift Knob and Boot

First, remove the gear shift knob and boot by unscrewing it from the top of the shifter. This should reveal a plastic or rubber boot that needs to be removed. Use pliers to carefully remove any clips that are holding the boot in place.

See also  How to Convert Your Subaru Forester into a Camper: The Ultimate Guide for Outdoor Enthusiasts

Step 2: Remove Center Console and Trim Panel

Next, remove the center console and trim panel by unscrewing any bolts or screws that hold it in place. Carefully pull the console back and remove the wiring harness that connects the console to the car’s electrical system. Set the console and trim panel aside.

Step 3: Remove Shifter Linkage

With the console and trim panel removed, you should be able to see the shifter linkage. Use a socket set to remove any bolts or screws that hold the linkage in place. Be sure to take note of where each bolt was located, as they may be different sizes or lengths.

Step 4: Remove Old Gear Shift

Now that the linkage is removed, you can remove the old gear shift from the car. This may require a bit of force, so be patient and work slowly to avoid damaging any parts. Once the old gear shift is removed, set it aside and clean the area where it was located.

Step 5: Install New Gear Shift

Install the new gear shift by aligning it with the mounting hole in the car and carefully sliding it into place. Use a torque wrench to tighten any bolts or screws that hold the gear shift in place. Be sure to follow the manufacturer’s torque specifications to avoid over-tightening and damaging the new gear shift.

Step 6: Reinstall Shifter Linkage

With the new gear shift in place, you can reattach the shifter linkage. Use the notes and photos you took earlier to ensure that each bolt is in the correct location. Use a torque wrench to tighten each bolt to the manufacturer’s specifications.

See also  How Much Do Drivers Read the Window in a 2015 Subaru Forester?

Step 7: Reinstall Center Console and Trim Panel

Once the linkage is reattached, you can reinstall the center console and trim panel. Carefully reconnect any wiring harnesses and ensure that all bolts and screws are in the correct location. Use a torque wrench to tighten each bolt to the manufacturer’s specifications.

Step 8: Reinstall Gear Shift Knob and Boot

Finally, reinstall the gear shift knob and boot by carefully sliding it back into place and screwing it onto the top of the shifter. Use pliers to reattach any clips that hold the boot in place.

Conclusion

By following these step-by-step instructions, you should be able to successfully change the manual gear shift of your Subaru Forester. Remember to take your time, be patient, and take notes and photos as you go to make reassembly easier. If you need help at any point in the process, don’t hesitate to consult with a mechanic or other professional.

FAQs

Q: Can I use any gear shift kit for my Subaru Forester?
A: No, it’s important to use the right gear shift kit for your specific make and model. Using the wrong kit can lead to compatibility issues and other problems.

Q: Do I need any special tools for this job?
A: Yes, you’ll need a few specialized tools, including a torque wrench and a transmission jack. Be sure to have these on hand before you begin.

Q: How long does it take to replace a manual gear shift?
A: The process can vary depending on your level of experience and the specific make and model of your Subaru Forester. However, you can expect the job to take a few hours to complete.

See also  How to Transport Your Bicycle in a Subaru Forester: The Ultimate Guide for Outdoor Enthusiasts
Avatar photo

Alton Brobst

As a longtime Subaru enthusiast, Alton brings a wealth of knowledge and experience to our blog. From his early days of tinkering with engines to his current role as a certified Subaru technician, Alton has seen it all when it comes to Subarus. When he's not working on cars, he enjoys hiking and exploring the great outdoors.

Recommended Articles